Safety Instructions
Make sure these instructions are read and completely understood before attempting assemble or use the GameZtation®.
• If you are unsure of any part of this instruction booklet, please contact a professional installer for assistance.
• The GameZtation® is designed for use by adults, indoors on flat level floor surfaces only
• Do not deploy or retract the GameZtation® when children are within 2mtrs of the unit
• Ensure that only the handles provided at the front of the support legs are held securely using two hands during the complete deployment and retraction process
• Ensure that fingers and electrical cables are not placed in the vicinity of the desk bracing mechanism during deployment or retraction
• Ensure that power to all electrical cables and equipment to be used in conjunction with the GameZtation® is turned off and disconnected from the wall during deployment and retraction.
• Ensure that all electrical cables and equipment to be used in conjunction with the GameZtation® are in good condition and meet the relevant Australian Standard requirements for such application
Warning
This product contains high pressure gas springs, do not put near, high temperature.
Thank you
Thank you for purchasing GameZtation® which as been designed here in Australia specifically as a super compact, mobile, computer workstation for those who love computer games
• GameZtation® is protected under Aust patent application #2021104938
• The monitor mounting system is designed to accept most vesa mounted screens and is suitable for use with gaming consoles, laptop computers, or with the addition of the GameZtation® caddy, Computer towers as well.
• The unit presents the opportunity to be collapsed and stored with in seconds when not in use.
• GameZtation® is manufactured from steel and aluminium components which are powder coated for appearance and durability.
• The desk height is 720mm from level ground which is the average height recommended by Workcover
Assembly Instructions
Your GameZtation® is factory assembled & tested and requires only fitment of the feet which are removed for transport and your monitor/ computer/console
Stage 1 Foot Installation
Step 1
Place the GameZtation® on an elevated horizontal surface with the base edge aligned with the vertical edge of the supporting structure, the desk support legs should be facing upwards as per figure 1
Step 2
Open the desk unit by lifting the desk surface, holding the angle handles on each leg.
Step 3
Retrieve the feet, screws and foot pedal from within the desk cavity and then close the desk unit.
Step 4
Fix the feet and foot pedal to the base of the unit using the 4 x M6 screws provided as per figure 4
Step 5
With the assistance of a second person lift the unit to the upright position and gently place on the ground/floor
Step 6
Deploy the GameZtation® module by depressing the foot pedal and allow the monitor pod and desk assembly to rise to it’s full height
Step 7
Using two hands open the desk holding both angle handles located at the top of each front leg
Step 8
Remove the monitor mount assembly from the mounting beam by pulling down on the mount retaining plunger and disengage the assembly from the monitor mounting beam
Step 9
Fix the Vesa screen mounting plate to the rear of your monitor screen using the 4 x M4 screws provided. You may adjust the screen angle by positioning the monitor mount bracket relative to the fixing plate and tightening the screws as shown
Step 10
Position your monitor in the GameZtation® pod by engaging the support tangs in the mounting beam and retracting the locking pin. When in position release the locking pin and test engagement of the locking pin in the mounting beam. Your monitor should now be securely fixed in the GameZtation® pod.
Step 11
The rear panel is provided with a cable access slot to enable power and associated cables to exit the pod. Remove the 2 x M8 screws from the desired access end of the rear panel, this will generally allow the rear panel to flex sufficiently to pass the cable ends through. Once the cables are in position reinstate the screws and align the cables neatly.
The GameZtation® is provided with edge gasket all round the cord ingress slots , ensure that this edge gasket is in place and is not damaged in anyway prior to use.
Cable ties are provided to retain the monitor drive and power cables behind the monitor rail.
Once the monitor is installed and cables connected, replace the rear cover panel and two lead keeper brackets which are provided to allow the power cord to be retained when not in use.
The desk is not designed for high loads, please ensure that the GameZtation® is used only in the fully deployed state with the chassis raised to its highest point and the desk surface horizontal.
Do not use the GameZtation® if it has suffered any mechanical damage due to misuse or overloading.
The locking gas struts installed in your GameZtation® have been selected to be suited to the average combined weight of the travelling desk and computer monitor and associated equipment. You may find that depending on the equipment that you install, the unit maybe either sluggish to raise or may require extra effort to push down when retracting.
Thank you for selecting GameZtation®, we trust you will enjoy many years of enjoyment from its use.